Pantry Door Storage #257 (08/01/2025) A storage system for a pantry door.

Align Miter Gauge #256 (05/21/2022) Align a miter gauge to 90 degrees using a dial indicator.

A Cherry Bed #255 (9/29/2021) I combined all four parts of this build into one, easy to watch, video.

Level Table Legs #254 (06/04/2021) Remove wobble (rock) from anything with four legs using a palm router and a mortising bit.

Through Tenon Bookcase #253 (04/30/2021) I make a through tenon bookcase from cherry.

Drawer Box Table Combined #252 (12/15/2020) I combined all three parts of the drawer box table build into one.

Wine Hutch (Complete) #251 (08/15/2020) I combined all five parts of the wine hutch build into one.

Moon Frame #250 (12/13/2019) I took a photo of the moon several months ago from my property using a telescope. I recently had a print made and it needed a frame. Birds e...

Build a Modern Hall Table #249 (11/15/2019) This project was originally published in 2015 in five videos. I combined all five into one video for convenience here.

Flatten Your Watestones #248 (11/08/2019) Quick and easily flatten waterstones using this method.

Chamfered Through Tenons #247 (10/28/2019) Use a hand plane to crreate chamfers on your through tenons.

Notched Top Table #246 (08/23/2019) A modern looking table with a top that is notched around the legs.

Laundry Hamper #245 (07/12/2019) Features bookmatched panels and curved rails.

Tiger Maple Cutting Board #244 (05/24/2019) A highly figured tiger maple cutting board. I demonstrate template routing using two different bearing bits.

Can Wax Ruin a Finish #243 (05/03/2019) I examined the influence wax has on an oil-based finish application.

Wine Hutch Build Part 5 #242 (04/19/2019) The finale of the wine hutch build.

Wine Hutch Build Part 4 #241 (03/22/2019) I finish the drawers and the shelves.

Wine Hutch Build Part 3 #240 (03/09/2019) I finished the top and the drawer support structure.

Wine Hutch Build Part 2 #239 (03/01/2019) In this segment I finish assembling the carcass.

Wine Hutch Build Part 1 #238 (02/15/2019) The legs, and rails are dimensioned. The joinery is also completed and a good start is made on the panels.

Samurai Mantel Clock #237 (01/18/2019) A mantel clock from cherry. Plans are available in my store.

Make a Fishtail Chisel #236 (11/30/2018) I made a set of fishtail chisels from a couple of old and cheap Buck Bros chisels.

Make a Wall Hanging Chisel Rack #235 (11/16/2018) I made a chisel rack which also holds my mallet. All conveniently located in the same place.

45 Degrees at the Table Saw Quickly and Accurately #234 (10/26/2018) Use a dial indicaor to align your table saw blade to 45 degrees. Keep the dial indicator plunger as...

Floating Tenons - Methods and Applications #233 (09/29/2018) A tutorial for making and using loose tenon joinery.

Sliding Dovetail Toggle Clamp #232 (07/27/2018) A quick way to make your toggle clamps more versatile.

Weather Station #231 (07/13/2018) Build a weather station. I made this from cherry and walnut.

How I Made a Lidded Box #230 (06/29/2018) A cherry lidded box for my wife.

Wine Box with Splined Miters #229 (06/15/2018) I made a wine box for my Dad's birthday from sapele. These make great gifts!

Shop Tour - What Works and What Doesn't #228 (06/08/2018) Shop Tour 2018

End Grain Tic Tac Toe Coasters #227 (05/25/2018) Coasters from maple and cherry scrap lumber. Easy and fun project.

Grizzly G0490X Jointer #226 (05/11/2018) Grizzly G0490X Jointer - Unboxing, Setup, Alignment and Impressions of my new jointer.

Double Curve Cutting Board #225 (05/04/2018) A cutting board that utilizes a neat curve making technique.

Modern Drawer Box Table Part 3 #224 (04/20/2018) I finish the table by completeing the drawer and the drawer box. Finished with General Finishes Arm-R-Seal

Modern Drawer Box Table Part 2 #223 (04/13/2018) The base is finished and the drawer box is almost complete.

Modern Drawer Box Table Part 1 #222 (03/29/2018) The carcass is dry assembled.

Ultimate Bird Feeder #221 (03/16/2018) A bird feeder with a hinged roof for easy feed loading.

A Triangle Waste Basket in Cherry #220 (03/02/2018) Covers stopped grooves and book matched panels.

Cherry Chisel Rack #219 (02/16/2018) A feature rich chisel rack with through tenons.

Double Picture Frame #218 (02/09/2018) Covers miter joints, blind halflap joints, and splines.

Revisit the Twin Screw Vise #217 (01/26/2018) My old vise did not require a lathe to build.

Dual Spline and Tenon Jig #216 (01/12/2018) Make a slot for splines and cut tenon cheeks all with the same jig.

Chisel Bevel Angle Jig #215 (12/21/2017) Easy to build and very useful.

A Cherry Bed Part 4 #214 (12/08/2017) The finale. Bed rail breakdown fastener hardware installation and more.

A Cherry Bed Part 3 #213 (11/30/2017) I glue up the headboard and ffotboard. Almost finished!

Wagner Moisture Meter Review #212 (11/27/2017) A review of the Wagner Meter pinless moisture meter. Model MMC220

A Cherry Bed Part 2 #211 (11/17/2017) This episode is all about the joinery!

A Cherry Bed Part 1 #210 (11/10/2017) I start on a bed for my son and discuss why is old bed is failing. I also show past projects in his room.

BESSEY Tools IBeam Clamp Review #209 (11/03/2017) Review of Bessey Tools IBeam clamp. This is a sponsored video.

BOSCH Glide Review #208 (10/30/2017) Review of the Bosch Glide GCM12SD.

Open Box Vase #207 (10/20/2017) A vase that was supposed to resemble a flower but looks more like a box.

Shoji Lamp #206 (10/13/2017) A shoji lamp made from sapele and rice paper. SketchUp File

Halloween Candy Pumpkin Tray #205 (09/29/2017) Made from cherry, and walnut with inlayed ebony eyes.

Make a Walnut and Maple Box #204 (09/22/2017) Walnut and maple box with wrap around walnut grain, splines and book matched maple panel top.

Rubber Band Cannon #203 (09/15/2017) Build a toy cannon that is powered by a rubber band.

Build a Bathroom Wall Shelf #202 (09/01/2017) An easy to build and very useful shelf.

Open Bookcase Part 3 #201 (08/25/2017) The finale. Shelves and ledgers.

Open Bookcase Part 2 #200 (08/18/2017) In this segment I finish the joinery and glue the carcass together.

Open Bookcase Part 1 #199 (08/11/2017) I designed an open -style bookcase, milled all the lumber and started on the joinery.

Align Jointer Tables Parallel with a Dial Indicator #198 (08/08/2017) A fast, easy and inexpensive solution to align a jointer. The tables can be checked for parallel a...

Picture Frame - Jurassic Edition #197 (07/21/2017) My dinosaur Rex makes a few appearances in this one.

Kitchen Drawer Organizer #196 (07/07/2017) I made a couple organizers for our kitchen drawers to replace an older one.

The Ultimate Bottle Opener #195 (06/23/2017) Made from mahogany and finished with polyurethane. This will be given away to a Patreon supporter.

Modern Desk Part 4 FINALE #194 (06/16/2017) I completeed the drawers for the desk and used a recessed drawer pull with walnut.

Modern Desk Part 3 #193 (06/09/2017) I completed and attached the drawer boxes.

Modern Desk Part 2 #192 (06/02/2017) Build a modern desk with a floating top and suspended drawers.

Modern Desk Part 1 #191 (05/26/2017) Build a modern desk with a floating top and suspended drawers.

Small Parts Sled - Align it Like a Ninja #190 (05/12/2017) I made a small parts table saw sled. I aligned it using a dial indicator. I also made my own adjustable runn...

Build a Headphone Stand #189 (05/05/2017) I made a headphone stand for my son for his computer.

Drill Press Table #188 (04/21/2017) I made a plastic laminate covered drill press table with DIY hold-downs.

Tilting Drill Press Vise #187 (04/14/2017) An all wood, tilting drill press vise. Plans are available in my Plans Store.

Captive Ring Baby Rattle #186 (04/07/2017) I made a captive ring baby rattle using a DIY ring releasing tool.

Drop Leaf Plant Stand Pt 2 #185 (03/31/2017) I completed the top and the sliding dovetail supports. SketchUp file is available:

Drop Leaf Plant Stand Pt 1 #184 (03/24/2017) I finished the base of the plant stand. Next up is the top including the drop leaves.

Adjustable Mouth Krenov Plane #183 (03/17/2017) Build an adjustable mouth Krenov style plane.

A Modern Lamp #182 (03/10/2017) Build a modern looking lamp with very little wood. Plans

Panel Bed Part 3 #181 (02/19/2017) The final segment of my panel bed build series. Thanks for watching. Get $75 off your Leesa mattress with promo code garageworks75 w...

Panel Bed Part 2 #180 (02/02/2017) This time I finish the joinery and the panels.

Panel Bed Part 1 #179 (01/24/2017) This is Part 1 of my panel bed build. Made from mahogany. I hope you dig it. Mattress: https://www.leesa.com/

Christmas Ornament #178 (12/21/2016) My first Christmas tree ornament made at the lathe.

Brick Endgrain Cutting Board #177 (12/09/2016) A brick end grain cutting board as a Christmas present.

Police Baton #176 (11/22/2016) I made a police baton from walnut and maple. Law Enforcement United: http://www.leunited.org/

Make a Sewing Box Pt 3 #175 (11/11/2016) I completed the sewing box.

Make a Sewing Box Pt2 #174 (10/28/2016) I finished the box and the lid. Moving on.

Make a Sewing Box Pt1 #173 (10/21/2016) Part 1 of the sewing box build.

Double Floating Tenons #172 (09/30/2016) Make double floating mortise and tenon joints with an easy to use fixture.

Padauk and Oak Bowl #171 (09/18/2016) I made my second bowl and I am auctioning it off two a viewer. Bid here: http://www.garagewoodworks.com/auction.php

Outdoor Table #170 (09/09/2016) An outdoor table, foot-rest to go with my Asian Inspired Bench.

Splined Picture Frame #169 (08/22/2016) Cherry picture frame with walnut splines. In loving memory of our dog Puddy.

Make a Carvers Mallet #168 (08/01/2016) A make a carvers mallet with my new Laguna lathe.

Asian Inspired Bench Part 4 #167 (07/15/2016) Done! Get the SketchUp file here.

Asian Inspired Bench Part 3 #166 (07/06/2016) I finished the second of three sub-assemblies. Come back for part 4 (finale).

Asian Inspired Bench Part 2 #165 (06/27/2016) I made great progress on my outdoor Asian inspired bench. I finished milling most of the parts. Most of the joinery is comp...

Asian Style Bench Part 1 #164 (06/14/2016) This is part 1 of a multi-part series for an Asian inspired sitting bench.

Router Table Fence Upgrade #163 (05/28/2016) I upgraded my router table fence to with a T-track for stops and other accessories.

A Modern Coat Rack #162 (05/19/2016) Build a modern looking coat rack. Coat hanger.

Cherry and Walnut Wall Shelf #161 (04/29/2016) Make a wall shelf with spline reinforced mitered corners.

Make a Marking Gauge #160 (04/16/2016) I made a marking gauge from walnut and cherry scrap. Quick and easy! Hardware: Point: #8-32 x 1.5 inch stainless socket cap scr...

Cherry Bookcase Part 4 #159 (03/26/2016) The final video for the series.

Cherry Bookcase Part 3 #158 (03/20/2016) In this episode I glue together the carcass and start on the shelves.

Cherry Bookcase Part 2 #157 (03/09/2016) This time I finish the joinery and the bookmatched panels.

Cherry Bookcase Part 1 #156 (02/27/2016) Build a bookcase along side me.

G&G Dart Holders #155 (02/01/2016) I finally got around to making a dart holder for my Greene and Greene dart board cabinet. Cabinet video: http://www.garagewoodworks.c...

Ultimate Resaw Fence #154 (01/17/2016) Build a resaw fence for your bandsaw. Adjusts for drift. Alignment jigs : http://www.garagewoodworks.com/Alignment.php

Breakfast Tray Part 2 #153 (01/03/2016) The final video in the Breakfast Tray series. We make a book-matched panel, glue together the bridle joint, make a proud finger ...

Breakfast Tray Part1 #152 (12/17/2015) My wife wanted me to build her a breakfast tray. So , here we go. I designed it in the G&G style with proud bridle joints and eb...

Sharpen Card Scrapers:A New Method #151 (11/21/2015) Sharpen card scrapers using an easy to build jig.

Lightsaber Candle Holder #150 (11/08/2015) Make a set of ligtsaber candle holders.

Edison Lamp Part 2 #149 (11/02/2015) A double pendant lamp with spayed legs. This is the final video.

Edison Lamp Part 1 #148 (10/21/2015) A double pendant lamp with splayed legs.

Make a Shop Stool Part 2 #147 (10/02/2015) Part 2 of 2 of a maple shop stool with splayed legs.

Make a Shop Stool Part 1 #146 (09/20/2015) Part 1 of 2 of a maple shop stool with splayed legs.

End Grain Cutting Board / Grizzly Drum Sander #145 (09/06/2015) Make a cool end grain cutting board in a day. This video is a project /tool review style video. The 16"...

Salad Tongs #144 (08/23/2015) Make a set of salad tongs in an afternoon.

Coin Tray #143 (08/04/2015) Make a coin tray using the X-carve from Inventables.

Align Miter Saw 90 #142 (07/25/2015) Align your miter saw to 90 degrees with a dial indicator.

Hall Table Build Part 5 #141 (07/03/2015) The finale!

Hall Table Build Part 4 #140 (06/28/2015) The drawer boxes get assembled and the drawers dovetailed.

Hall Table Build Part 3 #139 (06/18/2015) Joinery is finished and the carcass gets assembled.

Hall Table Build Part 2 #138 (06/13/2015) This time we finish the table carcass lumber milling and get ready for joinery.

Hall Table Build Part1 #137 (06/06/2015) An introduction and a little progress.

Pencil Holder with INCRA IBOX #136 (05/31/2015) Make a pencil holder with box joints using the INCRA IBOX.

Camera Crane #135 (05/23/2015) Build a camera crane to add kick to your videos.

Make a Trellis #134 (05/17/2015) Use a few half lap joints and make a trellis from pine.

Build a Pizza Cutter #133 (05/06/2015) Easy and fun project. All wood pizza cutter.

Shop Tour 2015 #132 (04/26/2015) Well, this is a shop tour. Not much else to say here.

G&G Chime Cover #131 (04/19/2015) Make a Greene and Greene chime cover with proud finger joints and ebony plugs.

Build a Krenov Style Hand Plane #130 (03/24/2015) A useful hand plane that can be made in a day.

Build a Monitor Stand #129 (03/18/2015) Works great for dual monitors. Slides out of the way when not in use.

Curvy Guitar Stand #128 (02/20/2015) An easy to make guitar stand with an elegant curve.

Challenge Coin Holder #127 (02/08/2015) Make a challenge coin holder in just a few hours.

Mortise Fixture #126 (01/26/2015) An easy to build mortise fixture for making floating tenon joinery. Also called loose tenon joinery. The plan is available for

Build a Clamp Rack #125 (1/08/2015) Build a clamp rack from plywood.

Ornaments at the DP #124 (12/08/2014) Make Christmas tree ornaments at the drill press using a series of rasps.

Router Bit Storage Part 2 #123 (11/25/2014) Router bit storage part 2. The carriages and top.

Router Bit Storage Part 1 #122 (11/14/2014) Make an easy to build, adjustable, router bit storage cabinet.

Turn Tool Handles at the Drill Press #121 (10/28/2014) Turn tool handles using rasps at the drill press.

Mortiser Template Copier #120 (10/17/2014) Make a template copier addition to your mortiser.

G&G Desk Part 6 #119 (10/03/2014) Greene and Greene desk. This time we finish glueing up the top and finish the breadboard ends. Visit Highland Woodworking for the...

G&G Desk Part 5 #118 (9/19/2014) I finish the sliding dovetail drawer slides, and the top.

G&G Desk Part 4 #117 (9/05/2014) Greene and Greene desk. This time we finish all the drawers.

G&G Desk Part 3 #116 (8/22/2014) Greene and Greene desk. This time we finish the glue up of the case and top side support. Visit Highland Woodworking for the

G&G Desk Part 2 #115 (8/07/2014) Greene and Greene desk. Finished mortising for joinery and created the indent detail and cloud lifts for the rails.

G&G Desk Part 1 #114 (7/31/2014) Greene and Greene desk: Lumber prep and a start. Part 2. Get the

Micro Adjust Your TS Fence #113 (7/06/2014) Really easy to build micro adjuster for your TS fence.

A Scoop from Cherry #112 (6/18/2014) An easy to make and very functional scoop.

Make a Birdhouse #111 (6/02/2014) Easy to build birdhouse from cedar.

Make a Lazy Susan #109 (5/09/2014) Made from cherry with a cool walnut and maple curve.

How to Sharpen Chisels #108 (4/27/2014) How I sharpen my chisels. The honing guide and angle gauge were purchased from Lee Valley.

Make a Desk Organizer #107 (3/28/2014) Made from cherry. Finsihed with a mixture of tung oil and varnish.

Cam Hook Clamp #106 (3/10/2014) Cross between a Bernoulli Spiral Clamp and a bench hook. Can easily replace your bench stops.

Make a Mallet #105 (2/17/2014) Made from walnut, maple and BBs. Plan from Shopnotes No2 1992.

Router Bowl #104 (2/12/2014) Make a bowl using a plunge router.

Dowel Drilling V-Block #103 (10/31/2013) Make a V-block for drilling dowels at top dead center.

Jointer Knife Setting Jig #102 (10/17/2013) Magnetic jigs for setting jointer knives. If your knives set too high you can use blue tape on the jig region that extends ov...

Build a Twin Screw Vise #101 (10/11/2013) Easy to build twin screw vise. Get the plans here.

DIY Bar Clamp #100 (10/03/2013) Really easy to build bar clamps.

Hanging Bird Feeder #99 (9/20/2013) Made from poplar and painted a nice shade of red.

Pin Router Attachment #98 (9/12/2013) Turn your router table into a pin router with this easy to build attachment.

Make a Hanging Hourglass #94 (8/06/2013) An interesting way to display an hourglass.

Make a Table Saw Fence Alignment Jig #93 (7/25/2013) Table saw fence alignment is crucial for clean and safe table saw rip cuts. This jig includes an adjustable miter...

Build a Modern Looking Clock #92 (7/19/2013) Made from cherry, spalted maple with walnut inlay.

Side Table Build-A-Long: Part 3 #91 (6/28/2013) The final installment for the series. We finish the drawer and top.

Side Table Build-A-Long: Part 2 #90 (6/21/2013) In this second part we finish the carcass and glue it together.

Side Table Build-A-Long: Intro and a Start #89 (6/14/2013) First GW build-a-long series. Great for beginners or intermediate woodworkers looking for a fun build.

Cherry Pencil Holder #88 (6/7/2013) Made from cherry and finished with a mixture of tung oil and varnish.

Pantry Shelves #87 (5/31/2013) Made from cherry ply and solid cherry edge banding.

Make a Few Drink Coasters #86 (5/24/2013) Made from cherry and using a DIY circle jig.

Align Table Saw Blade to 90° #85 (05/09/2013) Align your table saw blade to 90 with this easy to build jig. This same jig can also be used to align your fences to ...

Tilting Router Table Fence: Raised Panels & More #84 (5/03/2013) Make raised panels and splined miter joints using a tilting router table fence.

Tilting Router Table Fence #83 (4/26/2013) Make a router table that tilts both forward and back.

Make a Mancala Game #82 (4/19/2013) Made from maple with mahogany and walnut accents.

Splined Picture Frames #81 (4/12/2013) Make a couple picture frames with splined corners

Maple Lamps Part II #80 (4/05/2013) Part 2 of 2 for the maple lamps series.

Maple Lamps Part I #79 (3/29/2013) Make a couple maple lamps with curly maple panels.

Egg Holder #78 (3/20/2013) Make an egg holder for Easter.

Salt and Pepper Shakers #77 (3/13/2013) Make a set of salt and pepper shakers in an afternoon.

TV Stand Part 3 #76 (3/06/2013) In this episode we finish the tv stand and put it to use.

TV Stand Part 2 #75 (2/27/2013) Drawers and guides!

TV Stand Part 1 #74 (2/20/2013) Build a TV stand with me from cherry with exposed drawer sides. Part 1

Make some chopsticks #73 (2/13/2013) Made from cherry and walnut.

Sanding Block #72 (2/06/2013) Make an easy to build sanding block

Bagel Slicer #71 (1/30/2013) Make a bagel slicer that is easy and fun to build.

Bandsaw Template Jig #70 (1/19/2013) Make a bandsaw template jig.

Taper Jig #69 (1/14/2013) Build a tapering jig for the table saw.

Walnut Trash Can #68 (1/07/2013) Make a walnut trash can with book matched tapered sides.

Push Stick Modification #67 (12/16/2012) If a metal screw makes you uncomfortable then tap for a nylon screw.

Candle Holder #66 (12/11/2012) Make a candle holder from cherry.

Bottle Opener #65 (12/02/2012) Make a neat bottle opener.

Nut Cracker #64 (11/24/2012) A walnut nut cracker.

Cam Style Clamp Rack #63 (11/18/2012) Make an easy to build cam style clamp rack.

Sushi Plate #62 (11/10/2012) Make a sushi plate from cherry and walnut.

Adjustable Miter Bar #61 (11/2/2012) Make an adjustable miter bar that is immune to humidity changes.

Bandsaw Blade Tension Gauge #60 (10/28/2012) Make a bandsaw blade tension gauge.

Woodworking Safety #59 (10/21/2012) A Holloween woodworking safety video. A few woodworking safty rules to follow.

Build a small table saw sled #58 (10/14/2012) Build a small table saw sled and align it accurately.

A Groovy Band Saw Insert #57 (9/21/2012) Make a band saw insert from scrap lumber.

Raised Dog Feeder #56 (9/19/2012) Build a raised dog feeder from cherry. I used cocobolo for the wedges.

Capture Blade Angles #55 (9/3/2012) Accurately capture table saw blade angles. For better accuracy, make a sharpie mark on your blade and re-measure from the same spo...

Miter Stop #54 (8/22/2012) Make a miter stop.

Half-lapped Dovetailed Picture Frame #53 (8/9/2012) Make a half-lapped dovetailed picture frame.

Riving Knives and Splitters #52 (7/29/2012) How to check the alignment of riving knives and splitters.

You've Been Framed #51 (7/20/2012) You've Been Framed - A woodworking contest.

Curvy Cutting Board #50 (7/16/2012) Make a cool curvy cutting board.

Sneaky Tools #49 (7/8/2012) Ever wonder what happens to your lost tools?

How to sharpen your card scrapers #48 (6/27/2012) How to sharpen your card scrapers.

Peg Game #47 (5/27/2012) Make a cool peg game from scraps.

Cleaning Tenons to Width #46 (5/10/2012) Clean-up tenons to width at the router table. Error at 2:16 is 12 thou not 1 as stated.

Woodpeckers PRL V2 #45 (5/4/2012) Woodpeckers Precision Router Lift V2 Review.

Circle Jig 2.0 #44 (4/19/2012) Make a cool circle cutting jig.

Shop Tour 2012 #43 (4/08/2012) A fun tour of my shop taken in 2012.

Kerf Making Jig #42 (4/03/2012) A jig for making tight fitting dados. Quick and easy to build.

The Candle Holder #41 (3/22/2012) A neat re-build of an antique candle holder with a mirror backing.

5-Cut Method Showdown #40 (3/08/2012) A comparison of the 5-cut (five cut) method and dial indicator method.

Bernoulli Spiral Clamp #39 (2/19/2012) Introducing the Bernoulli Shell Clamp.

Step Stool part II #38 (2/18/2012) Build a cherry step stool (part II).

Step Stool part I #37 (2/10/2012) Build a cherry step stool (part I).

Coat Rack part II #36 (1/28/2012) Build a wall hanging coat rack (part II).

Coat Rack #35 (1/23/2012) Build a wall hanging coat rack (part I).

Knife Sharpen Jig Build #34 (11/08/2011) Build a planer and jointer knife sharpening jig.

Bookcase Recap #33 (7/15/2011) An entertaining video recap of the bookcase build.

TS Sled Alignment #32 (7/05/2011) How to align a table saw sled fence.

Bookcase PartVI #31 (6/25/2011) Part VI of Cherry Bookcase.

Bookcase PartV #30 (6/10/2011) Part V of Cherry Bookcase.

Bookcase PartIV #29 (5/23/2011) Part IV of Cherry Bookcase.

Bookcase PartIII #28 (5/14/2011) Part III of Cherry Bookcase. Joinery.

Bookcase PartII #27 (5/09/2011) Part II of Cherry Bookcase.

Bookcase PartI #26 (5/01/2011) Part I of Cherry Bookcase. In this video I demonstarte how I transform a 12/4 cherry slab into posts for a bookcase.

Toy Top #25 (2/27/2011) Make a wooden top (toy).

Transfer Angles #24 (1/30/2011) Transfer angles between your table saw blade and your jointer fence.

Circle Cutting Jig #23 (12/19/2010) Make a circle cutting jig for the bandsaw.

Chisel Plane (DIY) #22 (11/29/2010) Make a chisel plane that can be used as a shoulder plane or rabbeting plane.

Greene and Greene Frame 2 #21 (11/21/2010) Part 2 of the Greene and Greene inspired picture frame.

Greene and Greene Frame 1 #20 (11/18/2010) Part 1 of the Greene and Greene inspired picture frame.

Micro Adjust Your Fence #19 (10/31/2010) Demonstration on using a dial indicator to micro adjust your TS fence.

Chime Cover Part II #18 (10/18/2010) In this episode I finish the chime cover (doorbell).

Chime Cover Part I #17 (10/16/2010) In this episode I build a chime cover (doorbell) from cherry and walnut.

Horizontal Mortiser #16 (10/11/2010) Demonstration of my horizontal mortiser. Great for slot and groove creation. Get the plans here.

Table Saw Alignment #15 (9/16/2010) A quick method for finding and fixing table saw alignment problems. Just in case your miter slots are not parallel with each other,...

Flush Trim Saw Maintenance #14 (8/26/2010) Have you ever noticed that over time your flush trim saws begin to not behave very well? With repeated use the teeth can beg...

Sharpen Jointer Knives #13 (5/01/10) Process for sharpening jointer knives - scary sharp. You can hone the back side of the knife on the sandpaper to remove any bur...

G&G Indent Detail #12 (4/17/10) Process for creating Greene and Greene indent details.

Mitered Half-Laps #11 (3/27/10) Creating mitered half-laps.

Setting Jointer Knives #10 (3/13/10) A quick method for setting jointer knives.

Square a Miter Gauge #9 (2/20/10) An accurate method for squaring a miter gauge or a table saw sled. If you want, keep fine tuning the gauge until the needle has ev...

Thin Molding #8 (1/24/10) A safe method for creating thin molding at the router table. It might be better to index off of a clamped-down scrap piece of wood if you ...

Prepare Rough Lumber #7 (1/16/10) When you rip to final width, be sure to have the face jointed side down.

Floating Tenons #6 (12/29/09) How to make floating tenons. These are also called loose tenons.

Face Jointing Wide Boards #5 (12/13/09) How to face joint wide boards using a jointer and a hand plane.

Stopped Tapered Flutes #4 (12/4/09) An easy method for making stopped tapered flutes.

Shop Tour 2009 #3 (11/22/09) Take a tour of my woodshop (2009).

Planer and Jointer Sharpening Jig #2 (11/7/09) This is the old version.

Table Saw Blade Alignment #1 (11/4/09) How to align your table saw blade using a dial indicator and a quality square.