Video

	Level Table Legs #254 (06/04/2021) Remove wobble (rock) from anything with four legs using a palm router and a mortising bit.
	Flatten Your Watestones #248 (11/08/2019) Quick and easily flatten waterstones using this method.
	Chamfered Through Tenons #247 (10/28/2019) Use a hand plane to crreate chamfers on your through tenons.
	Can Wax Ruin a Finish #243 (05/03/2019) I examined the influence wax has on an oil-based finish application.
	Floating Tenons - Methods and Applications #233 (09/29/2018) A tutorial for making and using loose tenon joinery.
	Double Floating Tenons #172 (09/30/2016) Make double floating mortise and tenon joints with an easy to use fixture.
	Sharpen Card Scrapers:A New Method #151 (11/21/2015) Sharpen card scrapers using an easy to build jig.
	Ornaments at the DP #124 (12/08/2014) Make Christmas tree ornaments at the drill press using a series of rasps.
	Turn Tool Handles at the Drill Press #121 (10/28/2014) Turn tool handles using rasps at the drill press.
	How to Sharpen Chisels #108 (4/27/2014) How I sharpen my chisels. The honing guide and angle gauge were purchased from Lee Valley.
	Push Stick Modification #67 (12/16/2012) If a metal screw makes you uncomfortable then tap for a nylon screw.
	Adjustable Miter Bar #61 (11/2/2012) Make an adjustable miter bar that is immune to humidity changes.
	Bandsaw Blade Tension Gauge #60 (10/28/2012) Make a bandsaw blade tension gauge.
	Riving Knives and Splitters #52 (7/29/2012) How to check the alignment of riving knives and splitters.
	How to sharpen your card scrapers #48 (6/27/2012) How to sharpen your card scrapers.
	Cleaning Tenons to Width #46 (5/10/2012) Clean-up tenons to width at the router table. Error at 2:16 is 12 thou not 1 as stated.
	Circle Jig 2.0 #44 (4/19/2012) Make a cool circle cutting jig.
	Kerf Making Jig #42 (4/03/2012) A jig for making tight fitting dados. Quick and easy to build.
	5-Cut Method Showdown #40 (3/08/2012) A comparison of the 5-cut (five cut) method and dial indicator method.
	Bernoulli Spiral Clamp #39 (2/19/2012) Introducing the Bernoulli Shell Clamp.
	Knife Sharpen Jig Build #34 (11/08/2011) Build a planer and jointer knife sharpening jig.
	TS Sled Alignment #32 (7/05/2011) How to align a table saw sled fence.
	Transfer Angles #24 (1/30/2011) Transfer angles between your table saw blade and your jointer fence.
	Circle Cutting Jig #23 (12/19/2010) Make a circle cutting jig for the bandsaw.
	Micro Adjust Your Fence #19 (10/31/2010) Demonstration on using a dial indicator to micro adjust your TS fence.
	Table Saw Alignment #15 (9/16/2010) A quick method for finding and fixing table saw alignment problems. Just in case your miter slots are not parallel with each other,...
	Flush Trim Saw Maintenance #14 (8/26/2010) Have you ever noticed that over time your flush trim saws begin to not behave very well? With repeated use the teeth can beg...
	Sharpen Jointer Knives #13 (5/01/10) Process for sharpening jointer knives - scary sharp. You can hone the back side of the knife on the sandpaper to remove any bur...
	G&G Indent Detail #12 (4/17/10) Process for creating Greene and Greene indent details.
	Mitered Half-Laps #11 (3/27/10) Creating mitered half-laps.
	Setting Jointer Knives #10 (3/13/10) A quick method for setting jointer knives.
	Square a Miter Gauge #9 (2/20/10) An accurate method for squaring a miter gauge or a table saw sled. If you want, keep fine tuning the gauge until the needle has ev...
	Thin Molding #8 (1/24/10) A safe method for creating thin molding at the router table. It might be better to index off of a clamped-down scrap piece of wood if you ...
	Prepare Rough Lumber #7 (1/16/10) When you rip to final width, be sure to have the face jointed side down.
	Floating Tenons #6 (12/29/09) How to make floating tenons. These are also called loose tenons.
	Face Jointing Wide Boards #5 (12/13/09) How to face joint wide boards using a jointer and a hand plane.
	Stopped Tapered Flutes #4 (12/4/09) An easy method for making stopped tapered flutes.
	Planer and Jointer Sharpening Jig #2 (11/7/09) This is the old version.
	Table Saw Blade Alignment #1 (11/4/09) How to align your table saw blade using a dial indicator and a quality square.