 |
Level Table Legs #254 (06/04/2021) Remove wobble (rock) from anything with four legs using a palm router and a mortising bit. |
 |
Flatten Your Watestones #248 (11/08/2019) Quick and easily flatten waterstones using this method. |
 |
Chamfered Through Tenons #247 (10/28/2019) Use a hand plane to crreate chamfers on your through tenons. |
 |
Can Wax Ruin a Finish #243 (05/03/2019) I examined the influence wax has on an oil-based finish application. |
 |
Floating Tenons - Methods and Applications #233 (09/29/2018) A tutorial for making and using loose tenon joinery. |
 |
Double Floating Tenons #172 (09/30/2016) Make double floating mortise and tenon joints with an easy to use fixture. |
 |
Sharpen Card Scrapers:A New Method #151 (11/21/2015) Sharpen card scrapers using an easy to build jig. |
 |
Ornaments at the DP #124 (12/08/2014) Make Christmas tree ornaments at the drill press using a series of rasps. |
 |
Turn Tool Handles at the Drill Press #121 (10/28/2014) Turn tool handles using rasps at the drill press. |
 |
How to Sharpen Chisels #108 (4/27/2014) How I sharpen my chisels. The honing guide and angle gauge were purchased from Lee Valley. |
 |
Push Stick Modification #67 (12/16/2012) If a metal screw makes you uncomfortable then tap for a nylon screw. |
 |
Adjustable Miter Bar #61 (11/2/2012) Make an adjustable miter bar that is immune to humidity changes. |
 |
Bandsaw Blade Tension Gauge #60 (10/28/2012) Make a bandsaw blade tension gauge. |
 |
Riving Knives and Splitters #52 (7/29/2012) How to check the alignment of riving knives and splitters. |
 |
How to sharpen your card scrapers #48 (6/27/2012) How to sharpen your card scrapers. |
 |
Cleaning Tenons to Width #46 (5/10/2012) Clean-up tenons to width at the router table. Error at 2:16 is 12 thou not 1 as stated. |
 |
Circle Jig 2.0 #44 (4/19/2012) Make a cool circle cutting jig. |
 |
Kerf Making Jig #42 (4/03/2012) A jig for making tight fitting dados. Quick and easy to build. |
 |
5-Cut Method Showdown #40 (3/08/2012) A comparison of the 5-cut (five cut) method and dial indicator method. |
 |
Bernoulli Spiral Clamp #39 (2/19/2012) Introducing the Bernoulli Shell Clamp. |
 |
Knife Sharpen Jig Build #34 (11/08/2011) Build a planer and jointer knife sharpening jig. |
 |
TS Sled Alignment #32 (7/05/2011) How to align a table saw sled fence. |
 |
Transfer Angles #24 (1/30/2011) Transfer angles between your table saw blade and your jointer fence. |
 |
Circle Cutting Jig #23 (12/19/2010) Make a circle cutting jig for the bandsaw. |
 |
Micro Adjust Your Fence #19 (10/31/2010) Demonstration on using a dial indicator to micro adjust your TS fence. |
 |
Table Saw Alignment #15 (9/16/2010) A quick method for finding and fixing table saw alignment problems. Just in case your miter slots are not parallel with each other,... |
 |
Flush Trim Saw Maintenance #14 (8/26/2010) Have you ever noticed that over time your flush trim saws begin to not behave very well? With repeated use the teeth can beg... |
 |
Sharpen Jointer Knives #13 (5/01/10) Process for sharpening jointer knives - scary sharp. You can hone the back side of the knife on the sandpaper to remove any bur... |
 |
G&G Indent Detail #12 (4/17/10) Process for creating Greene and Greene indent details. |
 |
Mitered Half-Laps #11 (3/27/10) Creating mitered half-laps. |
 |
Setting Jointer Knives #10 (3/13/10) A quick method for setting jointer knives. |
 |
Square a Miter Gauge #9 (2/20/10) An accurate method for squaring a miter gauge or a table saw sled. If you want, keep fine tuning the gauge until the needle has ev... |
 |
Thin Molding #8 (1/24/10) A safe method for creating thin molding at the router table. It might be better to index off of a clamped-down scrap piece of wood if you ... |
 |
Prepare Rough Lumber #7 (1/16/10) When you rip to final width, be sure to have the face jointed side down. |
 |
Floating Tenons #6 (12/29/09) How to make floating tenons. These are also called loose tenons. |
 |
Face Jointing Wide Boards #5 (12/13/09) How to face joint wide boards using a jointer and a hand plane. |
 |
Stopped Tapered Flutes #4 (12/4/09) An easy method for making stopped tapered flutes. |
 |
Planer and Jointer Sharpening Jig #2 (11/7/09) This is the old version. |
 |
Table Saw Blade Alignment #1 (11/4/09) How to align your table saw blade using a dial indicator and a quality square. |
